WEKO3
アイテム
火花点火機関における熱流束計測の精度向上 : エンジン計測での薄膜型熱流束計の条件
http://hdl.handle.net/10458/3266
http://hdl.handle.net/10458/3266051aec5e-7025-4aec-aab2-340eef4e2638
| Item type | 学術雑誌論文 / Journal Article(1) | |||||
|---|---|---|---|---|---|---|
| 公開日 | 2011-05-30 | |||||
| タイトル | ||||||
| タイトル | 火花点火機関における熱流束計測の精度向上 : エンジン計測での薄膜型熱流束計の条件 | |||||
| 言語 | ja | |||||
| タイトル | ||||||
| タイトル | Improvement of Heat Flux Measurement on Combustion Chamber of Spark Ignition Engine : Conditions of Thin Film Type of Heat Flux Sensor for Heat Flux Measurement of Engine | |||||
| 言語 | en | |||||
| 言語 | ||||||
| 言語 | jpn | |||||
| キーワード | ||||||
| 言語 | en | |||||
| 主題Scheme | Other | |||||
| キーワード | Gasoline Engine, Heat Transfer, Measurement, Heat Flux, Sensor, Ferromagnetic | |||||
| 資源タイプ | ||||||
| 資源タイプ | journal article | |||||
| アクセス権 | ||||||
| 著者 |
長瀬, 慶紀
× 長瀬, 慶紀× 友松, 重樹 |
|||||
| 抄録 | ||||||
| 内容記述タイプ | Abstract | |||||
| 内容記述 | In this study, the experiments of heat flux measurements were carried out to improve the precision of heat flux sensor. Three kinds of heat flux sensors were made and used in the experiments. These are type-A1, type-A2 and type-B. The type-A1 is the sensor that the material of the sensor body is different from that of the combustion chamber wall, but the material of wire is same as that of the thin film on the sensor surface. The type-A2 is the sensor that the material of sensor body is same as that of the combustion chamber wall, and the material of wire is same as that of the thin film on the sensor surface. The type-B is the sensor that the material of sensor body is same as that of the combustion chamber wall, but the material of wire is different from that of the thin film on the sensor surface. In addition, the type-A1 is the only sensor of them that the materials are not magnetic. As the result, the requirement for the heat flux sensor is that the materials of wire and thin film must be the same. Ferromagnetic materials are not suitable to use for moving parts as the piston head of an engine. The material of sensor body does not need to use the same material of the combustion chamber wall. | |||||
| 言語 | en | |||||
| 書誌情報 |
ja : 日本機械学會論文集. B編 en : Transactions of the Japan Society of Mechanical Engineers. B 巻 76, 号 765, p. 859-864, 発行日 2010-05-25 |
|||||
| 出版者 | ||||||
| 出版者 | 日本機械学会 | |||||
| 言語 | ja | |||||
| 出版者 | ||||||
| 出版者 | The Japan Society of Mechanical Engineers | |||||
| 言語 | en | |||||
| ISSN | ||||||
| 収録物識別子タイプ | ISSN | |||||
| 収録物識別子 | 03875016 | |||||
| 書誌レコードID | ||||||
| 収録物識別子タイプ | NCID | |||||
| 収録物識別子 | AN00187441 | |||||
