WEKO3
アイテム
円筒歯車の曲げ負荷能力の向上に関する研究(第1報, 左右非対称歯形の採用による歯元応力及び剛性の変化)
http://hdl.handle.net/10458/763
http://hdl.handle.net/10458/76311dae1fe-f594-489b-9232-f04d49735e72
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
GangDeng13.pdf (732.2 kB)
|
|
| Item type | 学術雑誌論文 / Journal Article(1) | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 公開日 | 2007-10-17 | |||||||||||
| タイトル | ||||||||||||
| タイトル | 円筒歯車の曲げ負荷能力の向上に関する研究(第1報, 左右非対称歯形の採用による歯元応力及び剛性の変化) | |||||||||||
| 言語 | ja | |||||||||||
| タイトル | ||||||||||||
| タイトル | Bending Capacity Enhancement Using an Asymmetric Tooth Profile (1st Report, Infuluences of Pressure Angle on Tooth Root Stress and Bending Stiffness) | |||||||||||
| 言語 | en | |||||||||||
| 言語 | ||||||||||||
| 言語 | jpn | |||||||||||
| キーワード | ||||||||||||
| 言語 | en | |||||||||||
| キーワード | Gear, Tooth Profile, Pressure Angle, True Stress, Bending Stiffness, Load-sharing Ratio | |||||||||||
| 資源タイプ | ||||||||||||
| 資源タイプ | journal article | |||||||||||
| 著者 |
鄧, 鋼
× 鄧, 鋼
WEKO
5526
× 中西, 勉× 井上, 勝己 |
|||||||||||
| 抄録 | ||||||||||||
| 内容記述タイプ | Abstract | |||||||||||
| 内容記述 | This study is to develop a new method to enhance the bending capacity of gear tooth by the use of asymmetric tooth profile. Considering that many power transmission devices operate in one direction, where only one tooth surface （the front of tooth） is practically used. Therefore, it is not necessary to make tooth profile symmetrically, the back profile of tooth, which does not mesh in operation, can be designed to decrease tooth root stress. Different standard pressure angles are used to the front and back tooth profiles. Finite element method was used to calculate the tooth root stress and the bending stiffness of the asymmetrical tooth in several standard pressure angle combinations. Based on the results of calculations, it is clarified that tooth root stress decreases and bending stiffness increases remarkably by the use of a large standard pressure angle in the back profile of tooth, but no clear change in load sharing ratio appears during meshing period. | |||||||||||
| 言語 | en | |||||||||||
| 書誌情報 |
ja : 日本機械学會論文集. C編 en : Transactions of the Japan Society of Mechanical Engineers. C 巻 67, 号 656, p. 1139-1144, 発行日 2001-04 |
|||||||||||
| 出版者 | ||||||||||||
| 出版者 | 日本機械学会 | |||||||||||
| 言語 | ja | |||||||||||
| 出版者 | ||||||||||||
| 出版者 | The Japan Society of Mechanical Engineers | |||||||||||
| 言語 | en | |||||||||||
| ISSN | ||||||||||||
| 収録物識別子タイプ | ISSN | |||||||||||
| 収録物識別子 | 03875024 | |||||||||||
| 書誌レコードID | ||||||||||||
| 収録物識別子タイプ | NCID | |||||||||||
| 収録物識別子 | AN00187463 | |||||||||||
| 著者版フラグ | ||||||||||||
| 出版タイプ | VoR | |||||||||||
